#INSTAL THE NEW FOR IOS MEDIACODER HOW TO#
#INSTAL THE NEW FOR IOS MEDIACODER INSTALL#
#INSTAL THE NEW FOR IOS MEDIACODER UPGRADE#
#INSTAL THE NEW FOR IOS MEDIACODER SOFTWARE#
#INSTAL THE NEW FOR IOS MEDIACODER PC#

If you do not see the usual router prompt, you must use these next recommendations to continue with the upgrade procedure.

#INSTAL THE NEW FOR IOS MEDIACODER SOFTWARE#

If the router cannot properly load a Cisco IOS software image, it goes into one of these two modes which can be used for recovery and/or diagnostic procedures. Once you are connected to the console port of the router, you can see that the router is either in ROMmon or Boot mode.

#INSTAL THE NEW FOR IOS MEDIACODER HOW TO#

Once you are sure the console speed is set to 9600 bps on the router side, you must check the hyperterminal properties as previous.įor more information how to set the hyperterminal properties, see Applying Correct Terminal Emulator Settings for Console Connections. It is necessary to reload the router for a configuration register change to take effect. Check the value of the configuration register with the show version command (shown in the last line of the output) and ensure it is set to 0x2102 or 0x102. Note: If you get any garbage characters in the hyperterminal, this means you have not set the hyperterminal properties properly, or the configuration register of the router is set to a non-standard value for which the console connection speed is higher than 9600 bps. Open Hyperterminal on the PC, and use the next settings: Speed 9600 bits per second The console connection is made with a rolled cable (usually a flat black cable), and connects the console port of the router to the COM port of the PC. A direct console connection is preferred over a Telnet connection because most disaster recovery procedures require you to be physically present, and a Telnet connection gets lost during the reboot phase of the software installation. This can be done with a direct console connection or a virtual Telnet connection. Software Installation and Upgrade Procedures Step-by-Step Procedure Step 1: Establish a Console Session to the Router

#INSTAL THE NEW FOR IOS MEDIACODER PC#

Step 3: Download the Cisco IOS Software Imageĭownload the Cisco IOS software image into your workstation or PC from the Cisco Technical Support & Downloads. For additional information on how to select the right software version and feature set, see Compare Features to Select the Best Software Release. You can find the minimum recommended DRAM and Flash requirements in the release notes for each specific Cisco IOS software version, as well as in the Cisco Technical Support & Downloads.

Ensure that your router has enough Dynamic RAM (DRAM) and Flash for the Cisco IOS software image before you download the software version you have selected.

You can find this information with the Cisco Software Advisor (registered customers only). Verify that the Cisco IOS Software image that you download supports both your hardware and the required software features. Step 2: Select a Cisco IOS Software Image

#INSTAL THE NEW FOR IOS MEDIACODER INSTALL#

If the Cisco IOS software you install is larger than 16MB, you must use an FTP or RCP server. Note: Most TFTP applications cannot transfer files larger than 16MB in size. Note: A number of TFTP or RCP applications are available from independent software vendors or as shareware from public sources on the World Wide Web. Most TFTP applications provide a set-up routine to assist in these configuration tasks. This is the directory in which the Cisco IOS Software images are stored. Once the application is installed, a minimal level of configuration must be performed, use these steps:Ĭonfigure the TFTP application to operate as a TFTP server as opposed to a TFTP client. These Cisco series routers are addressed in this article:Ĭisco 7000 Series Routers with RP & RSP7000Ĭisco 10000 Series Internet Routers (ESR)Ĭisco uBR71xx, uBR 72xx, uBR10000 Series RoutersĪ Trivial File Transfer Protocol (TFTP) server, a Remote Copy Protocol (RCP) server, or a File Transfer Protocol Server (FTP) application must be installed on a TCP/IP-ready workstation or PC. Note: To use the troubleshooting tools described in this document, you must be a registered user and you must be logged in. The Cisco IOS software filenames can vary based upon the type of product used. The examples provided in this document are based on the 7500 router, but the procedure is applicable to other routers. This document discusses the procedure for upgrading your Cisco IOS software image on Cisco High-End routers. Conventionsįor more information on document conventions, see the Cisco Technical Tips Conventions. If your network is live, ensure that you understand the potential impact of any command. All of the devices used in this document started with a cleared (default) configuration. The information in this document was created from the devices in a specific lab environment. The information in this document is based on Cisco IOS Software Release 12.1 or later. See the Background Information section for specifics on these topics.

How to install Cisco IOS Software image.

Prerequisites RequirementsĬisco recommends that you have knowledge of these topics: This document describes how to upgrade your Cisco IOS ® software image on Cisco High-End routers.

Instal the new for ios MediaCoder